Diagnostics loop

14 posts / 0 new
Last post
Offline
Last seen: 1 year 11 months ago
Joined: Nov 12 2017 - 18:34
Posts: 30
Diagnostics loop

I recently acquired a IIe enhanced and when it's switched on it appears to enter the built-in diagnostics without any input from me. The usual screen images happen and the beeps at the end, however instead of a message it simply starts over. If I force it into diagnostics with the keyboard it goes through the routine and then gives me the "SYSTEM OK" message. I've removed and re-seated the ICs and thoroughly checked as well as cleaned the motherboard. It shows no corrosion or any signs of contaminants and looks very clean and undamaged.

Any suggestions as to what the cause could be would be much appreciated.

Offline
Last seen: 1 year 1 month ago
Joined: May 27 2009 - 01:37
Posts: 1002
Re: Diagnostics loop

Problem with OpenApple/ClosedApple or joystick buttons?

Offline
Last seen: 1 year 1 month ago
Joined: May 27 2009 - 01:37
Posts: 1002
Re: Diagnostics loop

Problem with OpenApple/ClosedApple or joystick buttons?

Offline
Last seen: 1 year 11 months ago
Joined: Nov 12 2017 - 18:34
Posts: 30
Re: Diagnostics loop

Problem with OpenApple/ClosedApple or joystick buttons?

Thanks for the response. It does the same thing when the keyboard is unplugged. I've heard that a bad LS251 could be the issue, but I'm hoping for suggestions that don't involve removing and replacing a soldered-in part. I don't know how to test the chip on-board so this may be my only option if nothing else is suggested. My hope is that someone has dealt with this before and can say with near certainty what it is.

jwg1962's picture
Offline
Last seen: 1 day 3 hours ago
Joined: Jan 29 2012 - 07:17
Posts: 363
Re: Diagnostics loop

Hi RuneRider,

There is an old tech trick you can try provided the chip is not shorted. Purchase a brand new LS251 chip and bend the legs slightly and place it down over the suspect LS251. Make sure the orientation is correct!!! i.e. the little notch in the one on the board matches the little notch direction on the one ou are placing down.

Make sure all the pins of the new one are making contact with all the pins of the one mounted to the board. Carefully turn the PC on and see if it works while carefully holding the new chip in place. If it does, then it is safe to de-solder and repair. If it doesn't then unfortunately that doesn't tell you much.

I'd then grab a copy of the SAMs repair guide for the Apple IIe. If you have an o-scope, that guide may give you an idea what should be coming from the chip.

Thanks,
Jay

Offline
Last seen: 3 days 21 hours ago
Joined: Dec 19 2008 - 21:01
Posts: 392
Re: Diagnostics loop

Note- without a keyboard connected, the diagnostics will always run as you describe.

However, what you describe is odd with the keyboard connected.

You tried another keyboard?

Offline
Last seen: 1 year 1 month ago
Joined: May 27 2009 - 01:37
Posts: 1002
Re: Diagnostics loop

Don't forget and check the 470 Ohm resistors. They pull PBO and PB1 to ground. And pressing CAPL or OAPL pull them high.

Offline
Last seen: 1 year 11 months ago
Joined: Nov 12 2017 - 18:34
Posts: 30
Re: Diagnostics loop

Hi RuneRider,

There is an old tech trick you can try provided the chip is not shorted. Purchase a brand new LS251 chip and bend the legs slightly and place it down over the suspect LS251. Make sure the orientation is correct!!! i.e. the little notch in the one on the board matches the little notch direction on the one ou are placing down.

Make sure all the pins of the new one are making contact with all the pins of the one mounted to the board. Carefully turn the PC on and see if it works while carefully holding the new chip in place. If it does, then it is safe to de-solder and repair. If it doesn't then unfortunately that doesn't tell you much.

I'd then grab a copy of the SAMs repair guide for the Apple IIe. If you have an o-scope, that guide may give you an idea what should be coming from the chip.

Thanks,
Jay

Might have to give that a try. Thanks.

Offline
Last seen: 1 year 11 months ago
Joined: Nov 12 2017 - 18:34
Posts: 30
Re: Diagnostics loop

Note- without a keyboard connected, the diagnostics will always run as you describe.

However, what you describe is odd with the keyboard connected.

You tried another keyboard?

Good to know. I don't have a keyboard I can use but that makes me think perhaps finding one is worth doing to see if it may be the issue.

Offline
Last seen: 1 year 11 months ago
Joined: Nov 12 2017 - 18:34
Posts: 30
Re: Diagnostics loop

Don't forget and check the 470 Ohm resistors. They pull PBO and PB1 to ground. And pressing CAPL or OAPL pull them high.

Thanks for the information.

Offline
Last seen: 1 year 11 months ago
Joined: Nov 12 2017 - 18:34
Posts: 30
Re: Diagnostics loop

I bought some IIe machines for parts and am hoping that swapping the keyboard will do the trick. If not I'll be doing more in-depth work.

Offline
Last seen: 1 year 11 months ago
Joined: Nov 12 2017 - 18:34
Posts: 30
Re: Diagnostics loop

I now have three more IIe machines. I swapped one of the keyboards into this machine and it now works perfectly. The machine with the donor keyboard arrived completely smashed by the shipper so it won't be needing it.

Thanks for all the advice!

Here2Learn's picture
Offline
Last seen: 1 year 1 week ago
Joined: May 22 2013 - 20:37
Posts: 177
Re: Diagnostics loop

Ouch. How was it packaged??

It is good that you got it figured out though.

Offline
Last seen: 1 year 11 months ago
Joined: Nov 12 2017 - 18:34
Posts: 30
Re: Diagnostics loop

Ouch. How was it packaged??

It is good that you got it figured out though.

It was an eBay buy. It shipped using the Global Shipping Program... in other words it had all the packing material removed by the people who repacked it at the eBay GSP center in Kentucky. I'm at about 75% damaged items when a seller uses the GSP to ship something I buy.

Log in or register to post comments