Hypertrol Inc HyperBOARD V1.10

11 posts / 0 new
Last post
Offline
Last seen: 5 hours 56 min ago
Joined: Jul 5 2018 - 09:44
Posts: 2538
Hypertrol Inc HyperBOARD V1.10

Anyone know anything about these?

 

https://www.ebay.com/itm/255338052174

Tom Owad's picture
Offline
Last seen: 2 hours 29 min ago
Joined: Dec 16 2003 - 15:14
Posts: 3349
A hint from MacWorld, August

A hint from MacWorld, August 1989:

HyperBoard 

Stand-alone data acquisition 
and process control board de- 
signed to extend functionality 
of HyperCard. Plugs in to the 
serial port, includes 32K RAM, 
and has on-board BASIC inter- 
preter. $139.95. HyperTrol, 
303/938-1662. 
Offline
Last seen: 5 hours 56 min ago
Joined: Jul 5 2018 - 09:44
Posts: 2538
Weird.  I wonder what the

Weird.  I wonder what the edge connector and slots are for?

 

Tom Owad's picture
Offline
Last seen: 2 hours 29 min ago
Joined: Dec 16 2003 - 15:14
Posts: 3349
Can you dump the ROM of a

Can you dump the ROM of a P8052AH?

Offline
Last seen: 5 hours 56 min ago
Joined: Jul 5 2018 - 09:44
Posts: 2538
I think so, but I'm not sure,

I think so, but I'm not sure, it has been a long time since I had anything to do with an 8052 type part.

Tom Owad's picture
Offline
Last seen: 2 hours 29 min ago
Joined: Dec 16 2003 - 15:14
Posts: 3349
Doesn' t look like they're

Doesn' t look like they're going to accept my $50 offer, and I'm not going to pay more than that for it with no software. I've attached photos from the listing, for anybody looking for this board in the future.

It's got the BASIC with the P8052AH-BASIC, 32K RAM, an RS-232 Transmitter/Receiver, and everything else is 7400 series. The barrel jack is down by the voltage regulator, so I'd imagine that's for power. RJ-11 is common for RS-232, albeit not on the Mac, but that's probably the serial port. The board is supposed to be for data acquisition and process control, but there's no I/O left besides the slots, so I would speculate they made various input cards to fit your application.

 

 

 

 

 

 

 

 

 

 

 

Offline
Last seen: 1 week 9 hours ago
Joined: Aug 18 2017 - 16:53
Posts: 164
Tom Owad wrote:Can you dump
Tom Owad wrote:

Can you dump the ROM of a P8052AH?

That's not necessary. These 8052AH-BASIC chips are well documented.

https://www.dos4ever.com/8031board/8031board.html

http://www.nomad.ee/micros/8052bas.shtml   with some URLs.

 

Regards

Ralf

 

 

Offline
Last seen: 5 hours 56 min ago
Joined: Jul 5 2018 - 09:44
Posts: 2538
Tom Owad wrote:Doesn' t look
Tom Owad wrote:

Doesn' t look like they're going to accept my $50 offer, and I'm not going to pay more than that for it with no software. I've attached photos from the listing, for anybody looking for this board in the future.

It's got the BASIC with the P8052AH-BASIC, 32K RAM, an RS-232 Transmitter/Receiver, and everything else is 7400 series. The barrel jack is down by the voltage regulator, so I

Well, there is the 16 pin socket marked "Socket" and the header connector marked "K1" so those could be for I/O.  I wonder if the slots use the Apple II pinout?  They're the right number of pins...

Tom Owad's picture
Offline
Last seen: 2 hours 29 min ago
Joined: Dec 16 2003 - 15:14
Posts: 3349
softwarejanitor wrote:Well,
softwarejanitor wrote:
Well, there is the 16 pin socket marked "Socket" and the header connector marked "K1" so those could be for I/O.  I wonder if the slots use the Apple II pinout?  They're the right number of pins...
 

Found a guy who had one:

Re:  Hooking up Mac to Aquarium / Data Acquisition
 by Tod Am » Fri, 18 Oct 1991 04:55:19

I've looked into this recently, and what I did was buy a very inexpensive
board from HyperTROL (in Boulder CO) which hooks up via the serial port.
The board has an 8 bit microcontroller (8052 I think) which you program in
basic via the serial port.  The board will run standalone and is easy to
interface with via Hypercard (calls to the serial port).  Right now mine is
being used as a fancy timer for a hydroponics setup.  The board is only $100.
Other cards are available for general D->A or A->D conversion.  They are a
bit more expensive and I'll probably build my own.  If you're willing to muck
around with hardware a bit but don't want to have to design everything, this
is probably a good way to go.
-tod

So there were A/D converters available for the sltos, but if the boards works standalone, you must be right about K1 or Socket.

Offline
Last seen: 5 hours 56 min ago
Joined: Jul 5 2018 - 09:44
Posts: 2538
If the designers were smart,

If the designers were smart, the 16 pin socket might be pinout compatible wih the Apple II game port.

 

Offline
Last seen: 1 week 9 hours ago
Joined: Aug 18 2017 - 16:53
Posts: 164
softwarejanitor wrote:Well,
softwarejanitor wrote:
Well, there is the 16 pin socket marked "Socket" and the header connector marked "K1" so those could be for I/O.  I wonder if the slots use the Apple II pinout?  They're the right number of pins...

 

No, it's not possible to built a Apple-II-Slot with these chips. The pinout must be different.

 

Some years ago I got a "standard" 8052 implementation of the late 1980s. In West-Germany sometimes called "EMUF":

http://www.ralf-kiefer.de/EMUF/8052AH_BASIC_BSb.JPG

There are 2 unpopulated sockets. You can develop some BASIC-Software with the BASIC interpreter (8kB or 32kB RAM), burn the program into an EPROM in one socket and put this EPROM into the other socket to run a small embedded system without need of interaction. There is a lot of I/O: GPIOs, AD and DA converter, two relais and a RTC.

 

The serial port is for the BASIC terminal, means you type in BASIC-Commands, you can start and stop the code similiar to other BASIC machines like Apple II, PET, C64.

 

Log in or register to post comments