Incorrect Disk II connection - How bad?

10 posts / 0 new
Last post
Offline
Last seen: 12 years 4 months ago
Joined: Jul 30 2011 - 14:47
Posts: 86
Incorrect Disk II connection - How bad?

Hi,

This is a stupid mistake. On connecting a Disk II drive to the interface card I managed to get the plug on with only one row of pins on the connector. I powered up the Apple but immediately noticed somthing wrong so switched off!

Now the drive spins up on power up but does not boot a disk. I have tried another drive and that is fine so it is not the interface card.

Is there a fix for this?

Any information gratefuly received.

Thanks, Richard.

Offline
Last seen: 8 years 4 months ago
Joined: Apr 10 2006 - 20:01
Posts: 1013
Re: Incorrect Disk II connection - How bad?
Offline
Last seen: 3 weeks 4 days ago
Joined: Dec 13 2005 - 08:40
Posts: 265
Re: Incorrect Disk II connection - How bad?

Sounds like you may have blown the read/write chip and maybe a diode on the disk drive II analog board. The chips are socketed, but the small diodes are soldered in. Being a diode they have be put in the same way. Make sure the black band is at the same end as the other you take out.

Best to pull the cover and look at the analog board with a large magnifing glass. Too see if any thing looks bad.

You should be able to see any damage to the diode, the yellow center will look black. The chip maybe. Sometimes you can, like a top blown off. I do not off the top of my head what the number of the chip is. But they are not real cheap either unless the price came down they are about $8.00.

Hope this helps

Offline
Last seen: 8 years 4 months ago
Joined: Apr 10 2006 - 20:01
Posts: 1013
Re: Incorrect Disk II connection - How bad?

Edit: this is the text cut from an archive of the FAQ -

I accidentally offset a row of pins on the //e disk controller card when plugging one of the drives in. Snap, crackle... you get the picture. I opened up my freshly fried Disk II, and in the center of the board there is a 74LS125 that is blown. Replaced it (it was socketed) with the same chip from another Disk II, and voila! it works again.

I would assume that misaligning the drive connector on the controller is what blew the 74LS125 in several Apple II drives before they got to me. Note
that while the genuine Apple Disk II simply lights the LED and doesn't move the
head at all when this IC was blown, a Mitac drive actually ate disks. So any
number of dead Apple II drives with different symptoms could have a blown
74LS125.

This is an archive of the FAQ entry:
http://web.archive.org/web/20060718212136/http://home.swbell.net/rubywand/Csa2FDRIVE.html#012

Offline
Last seen: 12 years 4 months ago
Joined: Jul 30 2011 - 14:47
Posts: 86
Re: Incorrect Disk II connection - How bad?

Hi,

Thanks for the help, very usefull as usual!

I have looked closely at the board and the diodes look ok. I suppose a quick check with a multimeter will give me more of a clue.

I have ordered some 74LS125's which should be with me tomorrow so fingers crossed!

Offline
Last seen: 8 years 4 months ago
Joined: Apr 10 2006 - 20:01
Posts: 1013
Re: Incorrect Disk II connection - How bad?

Great, you should have a ready supply of 125s on hand at all times. Wink

I mentioned in my first post, which I had to edit and had enormous trouble with the AppleFritter editing interface... anyway, once your drive gets into this state, it will eat floppies. Everything you insert will be instantly erased, even if it has a write-protect tab. Always be very careful aligning the pins on the header. Be paranoid about it. Use a bright light, and triple-check the alignment.

Offline
Last seen: 12 years 4 months ago
Joined: Jul 30 2011 - 14:47
Posts: 86
Re: Incorrect Disk II connection - How bad?

Thanks David,

I had one of the electrolytics go pop on one of my other drives and after replacing it I got the same symptoms.

Hopefully this will be a 125 as well !!

Offline
Last seen: 12 years 4 months ago
Joined: Jul 30 2011 - 14:47
Posts: 86
Re: Incorrect Disk II connection - How bad?

okay, some progress.

The drive I plugged in incorrectly has a fresh 125 chip and is working fine (hooray!)

The drive which 'popped' an electrolytic (C4) has a fresh 125 chip but still spins and wont boot (boo!)

If I try to format a disk through ADT Pro, the drive spins momentarily but is not recognized as an available drive. I have taken various voltage readings around the diodes and other components on tha analog board for this and a known good drive but all seems well. Could another chip have fried like the read or write amp? I have searched for these chips but none of my suppliers seem to have them. Are they obsolete or is there an equivalent. I'm frustrated with it now so I want to persevere to get it working!

As always, any info gratefuly received.

Cheers, Richard.

Offline
Last seen: 9 years 1 month ago
Joined: Sep 2 2011 - 21:23
Posts: 1
Re: Incorrect Disk II connection - How bad?

I got a disk II from eBay that had a popped C4 with the same symptoms. It turned out to be the read amplifier chip (probably in addition to the cap and the '125). I ended up getting one from Newark as a special order and of course found some on eBay for less once I had placed the order. I made a blog post about it as well: http://phantompinecone.wordpress.com/2011/02/01/resurrecting-an-apple-disk-ii/

I hope that's helpful.

Offline
Last seen: 12 years 4 months ago
Joined: Jul 30 2011 - 14:47
Posts: 86
Re: Incorrect Disk II connection - How bad?

Great, thanks for that.

I've just bought two of ebay so hopefully the drive will spring back to life!

Cheers,

Richard.

Log in or register to post comments