Help with MAC SE

9 posts / 0 new
Last post
robbo007's picture
Offline
Last seen: 3 days 22 hours ago
Joined: Dec 14 2011 - 06:39
Posts: 125
Help with MAC SE

Hi all,

i've just aquired a DIP SIM MAC SE and on the main logic board I've noticed there is a blowen cap at CR1, which is located left of the 5380 SCSI chip, above C9.

 Could someone tell me what replacement is needed and if there is a better resolution schematics? I've only found one which is very low res and very hard to read. 

Thanks,

dorkbert's picture
Online
Last seen: 1 hour 17 min ago
Joined: Apr 12 2009 - 16:33
Posts: 312
CE1 is not a cap. It's a 722

CR1 is not a cap. It's a 722 zener diode.

robbo007's picture
Offline
Last seen: 3 days 22 hours ago
Joined: Dec 14 2011 - 06:39
Posts: 125
ok thanks for clearing that

ok thanks for clearing that up. Do you know where I can locate a higer res schematics of the logic board?

Offline
Last seen: 3 hours 42 min ago
Joined: Jun 18 2010 - 13:54
Posts: 258
Have you loked here? https:/
robbo007's picture
Offline
Last seen: 3 days 22 hours ago
Joined: Dec 14 2011 - 06:39
Posts: 125
Thanks for that. Its a little

Thanks for that. Its a little more readable. 

 

What the voltage on the diode? Is it this? 

 

https://www.mouser.es/datasheet/2/268/LDS-0183-1-1592747.pdf

 

Cheers,

 

Offline
Last seen: 19 hours 11 min ago
Joined: Mar 31 2020 - 19:55
Posts: 383
robbo007 wrote:Thanks for
robbo007 wrote:

Thanks for that. Its a little more readable. 

 

What the voltage on the diode? Is it this? 

 

https://www.mouser.es/datasheet/2/268/LDS-0183-1-1592747.pdf

 

Cheers,

 

 

I have a few etra SE mainboards, so I can probably pull one and see if there is a p/n or useful markings. I would expect it to be a 1N722. The '22' here is the rated voltage. 

robbo007's picture
Offline
Last seen: 3 days 22 hours ago
Joined: Dec 14 2011 - 06:39
Posts: 125
Timelord wrote:robbo007 wrote
Timelord wrote:
robbo007 wrote:

Thanks for that. Its a little more readable. 

 

What the voltage on the diode? Is it this? 

 

https://www.mouser.es/datasheet/2/268/LDS-0183-1-1592747.pdf

 

Cheers,

 

 

I have a few etra SE mainboards, so I can probably pull one and see if there

ok thanks. I've managed to remove  the blown one but its was too far gone to see any markings on it to identify it.

robbo007's picture
Offline
Last seen: 3 days 22 hours ago
Joined: Dec 14 2011 - 06:39
Posts: 125
I've found some diodes on

I've found some diodes on amazon which work out cheaper. Can I just use any zener diode that has a voltage of 22v? 

Offline
Last seen: 19 hours 11 min ago
Joined: Mar 31 2020 - 19:55
Posts: 383
Delayed a bit. I will get you

Delayed a bit. I will get you the data ASAP. I woul not advide you to use an inappropriaate part. The properties of diodes like this are rather important.

Log in or register to post comments