Help with MAC SE

15 posts / 0 new
Last post
robbo007's picture
Offline
Last seen: 3 years 10 months ago
Joined: Dec 14 2011 - 06:39
Posts: 129
Help with MAC SE

Hi all,

i've just aquired a DIP SIM MAC SE and on the main logic board I've noticed there is a blowen cap at CR1, which is located left of the 5380 SCSI chip, above C9.

 Could someone tell me what replacement is needed and if there is a better resolution schematics? I've only found one which is very low res and very hard to read. 

Thanks,

dorkbert's picture
Offline
Last seen: 17 hours 47 min ago
Joined: Apr 12 2009 - 16:33
Posts: 373
CE1 is not a cap. It's a 722

CR1 is not a cap. It's a 722 zener diode.

robbo007's picture
Offline
Last seen: 3 years 10 months ago
Joined: Dec 14 2011 - 06:39
Posts: 129
ok thanks for clearing that

ok thanks for clearing that up. Do you know where I can locate a higer res schematics of the logic board?

Offline
Last seen: 2 hours 50 min ago
Joined: Jun 18 2010 - 13:54
Posts: 795
Have you loked here? https:/
robbo007's picture
Offline
Last seen: 3 years 10 months ago
Joined: Dec 14 2011 - 06:39
Posts: 129
Thanks for that. Its a little

Thanks for that. Its a little more readable. 

 

What the voltage on the diode? Is it this? 

 

https://www.mouser.es/datasheet/2/268/LDS-0183-1-1592747.pdf

 

Cheers,

 

Offline
Last seen: 2 years 7 months ago
Joined: Mar 31 2020 - 19:55
Posts: 848
robbo007 wrote:Thanks for
robbo007 wrote:

Thanks for that. Its a little more readable. 

 

What the voltage on the diode? Is it this? 

 

https://www.mouser.es/datasheet/2/268/LDS-0183-1-1592747.pdf

 

Cheers,

 

 

I have a few etra SE mainboards, so I can probably pull one and see if there is a p/n or useful markings. I would expect it to be a 1N722. The '22' here is the rated voltage. 

robbo007's picture
Offline
Last seen: 3 years 10 months ago
Joined: Dec 14 2011 - 06:39
Posts: 129
Timelord wrote:robbo007 wrote
Timelord wrote:
robbo007 wrote:

Thanks for that. Its a little more readable. 

 

What the voltage on the diode? Is it this? 

 

https://www.mouser.es/datasheet/2/268/LDS-0183-1-1592747.pdf

 

Cheers,

 

 

I have a few etra SE mainboards, so I can probably pull one and see if there

ok thanks. I've managed to remove  the blown one but its was too far gone to see any markings on it to identify it.

robbo007's picture
Offline
Last seen: 3 years 10 months ago
Joined: Dec 14 2011 - 06:39
Posts: 129
I've found some diodes on

I've found some diodes on amazon which work out cheaper. Can I just use any zener diode that has a voltage of 22v? 

Offline
Last seen: 2 years 7 months ago
Joined: Mar 31 2020 - 19:55
Posts: 848
Delayed a bit. I will get you

Delayed a bit. I will get you the data ASAP. I woul not advide you to use an inappropriaate part. The properties of diodes like this are rather important.

robbo007's picture
Offline
Last seen: 3 years 10 months ago
Joined: Dec 14 2011 - 06:39
Posts: 129
Hi, Did you manage to check

Hi, Did you manage to check this or are you still really busy? 

Thanks,

 

Offline
Last seen: 2 years 7 months ago
Joined: Mar 31 2020 - 19:55
Posts: 848
robbo007 wrote:Hi, Did you
robbo007 wrote:

Hi, Did you manage to check this or are you still really busy? 

Thanks,

 

Oh, bugger. In fact, I forgot entirely. TY for the reminder.

robbo007's picture
Offline
Last seen: 3 years 10 months ago
Joined: Dec 14 2011 - 06:39
Posts: 129
No problem. Let me know when

No problem. Let me know when you can. The darn schematics are so badly scanned they are near impossible to read.

Offline
Last seen: 2 years 7 months ago
Joined: Mar 31 2020 - 19:55
Posts: 848
robbo007 wrote:No problem.
robbo007 wrote:

No problem. Let me know when you can. The darn schematics are so badly scanned they are near impossible to read.

I'll try this week. I ust checked in and saw that you still need this. Haven't been well of late, so everything is slow for me. 

Offline
Last seen: 2 years 7 months ago
Joined: Mar 31 2020 - 19:55
Posts: 848
robbo007 wrote:No problem.
robbo007 wrote:

No problem. Let me know when you can. The darn schematics are so badly scanned they are near impossible to read.

 

 

 Sorry for taking an eternity to get around to this; here is a close-up photo of the board.

 

 

 

 

Note that on this board, it is above C5, not C9. Could you verify that marking?

As for replacing it: 

The part is 1N4006 (1A, 800V), as far as I can tell. The p/n is partially obscured due to how it is positioned. I dook another loo at an angle, and 1N4006 seems right. 

 

Here is a datasheet:

https://www.digikey.com/product-detail/en/on-semiconductor/1N4006/1N4006FSTR-ND/976986

 

https://www.mouser.com/ProductDetail/ON-Semiconductor/1N4006RLG?qs=y2kkmE52mdM%2FTiOsfUnWMw%3D%3D

https://www.mouser.com/ProductDetail/Diodes-Incorporated/1N4006-T?qs=rGAXPo9uwV1ds0CiDz9UCA%3D%3D

 

Either of those should be a good cross. 

robbo007's picture
Offline
Last seen: 3 years 10 months ago
Joined: Dec 14 2011 - 06:39
Posts: 129
Sorry for the lack of reply.

Sorry for the lack of reply. I managed to locate the diode and I've installed it. Mac booted up perfectly. Hard disk is alive still and has old data from a local council. I'll be investigating as soon as some RAM Simms repalcements arrive. My RAM was bad and I need !MB to load into the version of MacOS that is installed on the hard disk.

 

Thanks for all the help.

Regards, 

Log in or register to post comments