Disk II rainbow ribbon cable color pinout

18 posts / 0 new
Last post
hackerb9's picture
Offline
Last seen: 7 months 3 weeks ago
Joined: Sep 13 2005 - 08:35
Posts: 17
Disk II rainbow ribbon cable color pinout

Hi everyone,

I'm just doing a simple 20-pin IDC cable replacement for an old Disk II drive clone (technically a "Fourth Dimension Super Drive") and for fun wanted to use a pretty rainbow colored ribbon cable, like what the older Disk IIs used. But, Wikipedia's entry for the Disk II pinout colors seems to only cover the 19-pin Unidisk-style connector, so the colors for pins 17, 19, and 20 are likely incorrect. I'm guessing they should be violet, white, and black, respectively. Can anybody confirm that?

 

 
Disk II Header PinD-19 PinD-19 ColorSignal NameDescription
11BrownGNDGround
211RedSEEKPH0Phase 0 stepper
32OrangeGNDGround
412YellowSEEKPH1Phase 1 stepper
53GreenGNDGround
613BlueSEEKPH2Phase 2 stepper
74VioletGNDGround
814GreySEEKPH3Phase 3 stepper
95White-12V-12 volt supply
1015BlackWRREQWrite request
116Brown+5V+5 volt supply
1216Red+5V+5 volt supply
137Orange+12V+12 volt supply
1417YellowDR2 (ENABLE)Drive 2 select /Drive enable
158Green+12V+12 volt supply
1618BlueRDDATARead data signal
17 (Violet?)??+12V+12 volt supply
1819GreyWRDATAWrite data signal
19 (White?)??+12V+12 volt supply
20 (Black?)10WhiteWRPROTWrite protect
x9VioletEXINTExternal interrupt

 

Thanks!

 

PTB
Offline
Last seen: 5 hours 6 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
This is what was on the disk

This is what was on the disk ][ drive I had.

 

 

Cheers

Dave

Online
Last seen: 1 hour 41 min ago
Joined: Feb 27 2021 - 18:59
Posts: 466
IEC

The "rainbow" colored ribbon is in fact made according to the IEC numeric color code, because its purpose is quick signal identification and not being pretty. Accordingly, the signal number modulo 10 is carried by the colored wire with that weight in the IEC code (which all hobbyists know from through-hole resistor stripes).

PTB
Offline
Last seen: 5 hours 6 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
Cool info. Ive messed about

Cool info. Ive messed about with ribbon cable since i was a kid and i never knew that. Seems so obvious now. 

MacFly's picture
Offline
Last seen: 4 days 8 hours ago
Joined: Nov 7 2019 - 13:49
Posts: 442
PTB wrote:Cool info. Ive
PTB wrote:

Cool info. Ive messed about with ribbon cable since i was a kid and i never knew that. Seems so obvious now. 

Same! :D

hackerb9's picture
Offline
Last seen: 7 months 3 weeks ago
Joined: Sep 13 2005 - 08:35
Posts: 17
Thanks!
robespierre wrote:

The "rainbow" colored ribbon is in fact made according to the IEC numeric color code, because its purpose is quick signal identification and not being pretty. Accordingly, the signal number modulo 10 is carried by the colored wire with that weight in the IEC code (which all hobbyists know from through-hole resistor stripes).

Yes, the resistor code is what I was guessing, which is how I extrapolated pins 17, 19, and 20. Too bad Apple could not keep the same code when they switched to the DB-19 connector.

Another question: It seems like manufacturers sell IDC cables with the polarizing key (the bump that keeps you from putting it in backwards) flipped on one or both of the connectors. The original Disk II cables didn't do that, right? Would this $3 cable from Digikey work?

Offline
Last seen: 2 months 2 hours ago
Joined: Dec 19 2003 - 14:45
Posts: 219
Mnemonic for Resistor Code

Back in EE school, they taught us:

 

Better

Be

Right

Or

Your

Great

Big

Venture 

Goes

West!

Online
Last seen: 1 hour 41 min ago
Joined: Feb 27 2021 - 18:59
Posts: 466
cables

Cables are not always wired 1-to-1 on both ends. They can be wired in a multitude of different ways which makes reverse engineering a chore. There are, however, some configurations that are more common and therefore "defaults", which are straight-thru (Side A's Pin X connected to Side B's Pin X and only that pin), and roll-over (Side A's Pin X connected to its mirror image on Side B and only that pin). Roll-over cables are "symmetric" in the sense that if you hold the cable flat and look into each end, the cable turns 180° but doesn't flip over.

Ribbon cables are a little bit easier to decode since you can see the wires for almost their whole length, making it obvious if any have changed places (like the twisted sections in PC floppy drive harnesses). There are still some variations, since the connectors can be crimped on in 4 different ways: on the top or on the bottom, and facing "left" or "right" as respects to the polarizing tab. That's equivalent to two wiring patterns, coincidentally being straight-thru and roll-over.

It would make more sense explained in the language of group theory (symmetries and rotations).

A roll-over configuration is easier to implement if you have, say, two chassis on the desk, with their ports facing each other, and the cable goes from a horizontally-mounted board in one to another horizontal board in the other chassis. You could cable them together using regular box-headers without introducing a twist in the cable.

The Disk II cables are captive to the drives, so I don't know whether they are straight-thru or roll-over.

hackerb9's picture
Offline
Last seen: 7 months 3 weeks ago
Joined: Sep 13 2005 - 08:35
Posts: 17
Thanks!

It would make more sense explained in the language of group theory

 

If that's what I need for it to make more sense, then I am in serious trouble. ☺ The only thing I remember from math class is:

 

What is purple and commutes?

 

An Abelian Grape!

 

Offline
Last seen: 2 days 11 hours ago
Joined: Apr 26 2016 - 08:36
Posts: 661
robespierre wrote:The Disk II
robespierre wrote:

The Disk II cables are captive to the drives, so I don't know whether they are straight-thru or roll-over.

No they aren't.

 

The cables are straight conected ribbons with IEC20s on both ends (in the case of the metal Disk II)

And they are not captively attached to the drive.  Not in the metal Disk II nor in the plastic Unidisk 5.25 (or Apple 5.25)

 

 

 

Offline
Last seen: 8 hours 14 min ago
Joined: Dec 19 2008 - 21:01
Posts: 392
baldrick wrote:robespierre
baldrick wrote:
robespierre wrote:

The Disk II cables are captive to the drives, so I don't know whether they are straight-thru or roll-over.

No they aren't.

 

The cables are straight conected ribbons with IEC20s on both ends (in the case of the metal Disk II)

And they are not captively attached to the drive.  Not in the metal Disk

 

They certainly are, trapped inside the case. That is functionally "captive".

 

PTB
Offline
Last seen: 5 hours 6 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
Hi hackerb9, Here's some

Hi hackerb9,

 

Here's some photos of the ends as requested.

 

 

 

 

Cheers

 

Dave

hackerb9's picture
Offline
Last seen: 7 months 3 weeks ago
Joined: Sep 13 2005 - 08:35
Posts: 17
Thank you, Dave!

That picture is worth a thousand and twenty-four words!

hackerb9's picture
Offline
Last seen: 7 months 3 weeks ago
Joined: Sep 13 2005 - 08:35
Posts: 17
Close, but not quite

I got the $3 cable I linked to above and I just wanted to let people know to not get that one. It has two problems: First, the connector pictured on the left should be pointing down, not up. Second, it has "strain relief" which means the ribbon passes through part of the connector and then back into it before the insulation-displacement "teeth" bite into it. Both of those issues cause the ribbon to bulge out on the flat (non-keyed) side of the connector. However, the pin headers on the Apple ][ Disk drive and controller card slide that side against the printed circuit board, so any bump makes it not fit.

 

Electrically, the cable is correct and does work. I was able to cut off the strain relief and sort of shimmy the connector into place. Even so,  I don't like how it bends the pins away from the board, so I will keep searching to find one more like the original Apple ribbon cable.

Offline
Last seen: 2 days 11 hours ago
Joined: Apr 26 2016 - 08:36
Posts: 661
You don't need to use

You don't need to use connectors with strain relief.  And forget buying pre-made assemblies - that's a waste of money.

Any straight 20-pin connector is adequate.  Digikey, Newark and Mouser all have dozens of suitable connectors in various colours.

Pick one:

https://www.digikey.com/en/products/filter/free-hanging-panel-mount/316?s=N4IgjCBcoBw1oDGUBmBDANgZwKYBoQB7KAbXAGYB2SgTgDYQBdAgBwBcoQBlNgJwEsAdgHMQAXzEEATKRD8AJogAEiQoME5EbQryZigA

 

Want a blue one?  Here:

https://www.digikey.com/en/products/detail/cw-industries/CWR-227-20-0203/1122595

 

So if you don't like the loop-around strain releif, cut the connector off and crimp on one of the above.  All you need to do that is a small vise, but I've gotten away with a pair of "Channel-Lock" pliers to crimp the connector together.

 

hackerb9's picture
Offline
Last seen: 7 months 3 weeks ago
Joined: Sep 13 2005 - 08:35
Posts: 17
Pre-made versus home-made
baldrick wrote:

You don't need to use connectors with strain relief.  And forget buying pre-made assemblies - that's a waste of money.

Any straight 20-pin connector is adequate.  Digikey, Newark and Mouser all have dozens of suitable connectors in various colours.

 

Thanks, Baldrick. I've had bad luck in the past trying to hand crimp an IDC connector without the proper tools, so I figured I'd save myself the grief and just have it professionally done. Also, that reduces the risk that I blow up some IC because I miswire it. And, finally, while I was willing to pay more to get one pre-assembled, it was surprising to me how cheap it could be. In the above example, I paid $2.95, which is not bad compared to buying two headers and a length of ribbon cable as separate parts.

 

All that said, I will likely do as you suggest. I don't see how to specify on Digikey which direction the connector should point. 

Offline
Last seen: 2 days 11 hours ago
Joined: Apr 26 2016 - 08:36
Posts: 661
hackerb9 wrote:All that said,
hackerb9 wrote:
All that said, I will likely do as you suggest. I don't see how to specify on Digikey which direction the connector should point. 

That's up to you.  As long as both connectors are the same orientation relative to the ribbon you'll be fine.  Mind "pin 1" on both ends.

 

hackerb9's picture
Offline
Last seen: 7 months 3 weeks ago
Joined: Sep 13 2005 - 08:35
Posts: 17
 I think I figured it out.

 I think I figured it out. The keyword needed to get the right cable is "REVERSED" — not to be mistaken for "REVERSE WIRING", which puts the red stripe on the wire farthest from pin 1 on the socket!  "REVERSED" means that one IDC socket points up relative to the ribbon cable and the other points down.

Unfortunately, at least at Digikey, purchasing an assembled cable with a connector type of "socket to socket, REVERSED" costs $17 and has a standard lead time of over 11 weeks. I don't get why Digikey will custom assemble a non-stocked, "value added" cable for three bucks and ship it out the same day, but they can't turn one of the connectors upside down.

Oh well, as Baldrick said, I guess it's up to me to do it right. ☺

 

Log in or register to post comments