Apple II

Apple II Europlus Video fault

Submitted by trickydee on November 19, 2013 - 7:05pm

I am restoring an apple ii europlus and was getting quite far until the video output totally failed. I have started some initial chip swapping but I was hoping that someone could advise on where to troubleshoot further.

Forums: 
Apple II

Best Method for Connecting Marinetti to the Internet

Submitted by Clyde1992 on November 19, 2013 - 5:13pm

Hello, everyone:

A week ago, I finally received a CFFA3000, which has made transferring and running programs on my IIGS much easier. Now that the lack of mass storage is not an issue, I have decided install Marinetti, in order to connect my IIGS to the internet. I know that Marinetti is compatible with Ethernet, but Apple II Ethernet cards are not very common. I also do not have access to dial-up internet, so a dial-up modem is not an option. Therefore, I feel that the best solution would be to connect to the internet through the IIGS serial port.

Forums: 
Apple II

Microsoft CATS, Softcard II, Does anyone have CPM 2.28B disk image?

Submitted by rekokut on November 18, 2013 - 2:28pm

Hi guys!!!

First time posting here :).

I have this Microsoft CATS, Softcard II for the apple II :).

I am looking for a CPM 2.28B disk image for it. Others CPM versions wont work.

I found this link showing the information, but its very old post. Wondering if anyone has it could email me.

thinkinginventor@gmail.com

Forums: 
Apple II

CFFA3000 and AppleWorks

Submitted by dramsey on November 18, 2013 - 12:10pm

Is is possible to use AppleWorks to save a file to a CFFA3000 virtual disk? I have the AppleWorks disks in emulated Drive 1 and a blank disk in emulated Drive 2. DOS and ProDOS can read and write the emulated disk just fine, but AppleWorks says "Can't write to disk" when I try to save something to it.

If I try to format the emulated disk 2 from inside AppleWorks, it says there's a problem with the drive speed.

Any ideas?

Forums: 
Apple II

Peripheral card info help

Submitted by Zan8675 on November 17, 2013 - 8:32am

Got me an MPC Peripherals Corp Apple ][ Memory Module. Problem is I have not a clue what the switch on end of card is for (exactly like the switch on the Apple ][ rom card)
Could not find any documentation online so thought perhaps someone here could help?

If pictures needed I can do that just no access to take and post them right now. Could post photo later this morning/afternoon if needed.

Forums: 
Apple II

Just bought my first Apple ///

Submitted by jwg1962 on November 15, 2013 - 8:02pm

Just found and bought my first Apple /// - Stroke of luck!

Forums: 
Apple II

a2m2010 apple monitor contrast question

Submitted by mrathlon1700 on November 15, 2013 - 5:21pm

Had a simple dumb question. I have a a2m2010 monitor. When I adjust rear brightness control just before there's lines on the screen. How far should the side contrast control be up. Does the contract on those monitors get that bright?

For a decent picture I need to turn it up 80-85 percent on the contrast knob. I admit like it all the way turned up almost near the brighness.

Wondering if its normal. Weak tube?

Thanks

Casey

Forums: 
Apple II

"remove write protect tab" message

Submitted by TechChallenged on November 14, 2013 - 3:41pm

My system is an Apple IIe ][ with a DuoDisk controlled by a 655-0101 IO card. After years of reliable operation a problem has developed.

I get false "remove write protect tab" messages when trying to read Visifile or Appleworks data discs even though these discs are notched with no tabs. These data discs cannot be read. The message also appears when trying to initialize blank discs with DOS or ProDos masters, again notched with no tabs. Discs cannot be initialized. These problems exist on both drives.

Forums: 
Apple II

"Remove Write Protect Tab" message

Submitted by TechChallenged on November 14, 2013 - 3:39pm

My system is an Apple IIe ][ with a DuoDisk controlled by a 655-0101 IO card. After years of reliable operation a problem has developed.

I get false "remove write protect tab" messages when trying to read Visifile or Appleworks data discs even though these discs are notched with no tabs. These data discs cannot be read. The message also appears when trying to initialize blank discs with DOS or ProDos masters, again notched with no tabs. Discs cannot be initialized. These problems exist on both drives.

Forums: 
Apple II

Robotics Kit for Apple II I just acquired

Submitted by Zan8675 on November 13, 2013 - 5:54pm

So made a trip to Allentown, PA recently (about 80 miles from where I live in NJ) and picked up a Platinum //e and a Robotics kit. The control board, interface card, instruction manual and VHS instruction tape are still sealed in their original packaging. The arms, joysticks and battery eliminators are loose. Just curious what people's reactions are to this stuff since I have NEVEr looked into the value of robotics (other than how much I spent on Mindstorms stuff over the years for my son and I)
Zan

Forums: 
Apple II

Pages

Subscribe to Apple II