Drive not working after being in storage

15 posts / 0 new
Last post
Offline
Last seen: 2 years 2 months ago
Joined: Sep 23 2022 - 21:30
Posts: 3
Drive not working after being in storage

I recently pulled out a Disk ][ that had been kept in a drawer for several years. It was working when I put it away, but now it's not.

It powers up and makes the normal head banging sounds if I try to boot from it but then just spins the disk forever.

If I boot from another drive and try to read from it or format a disk with it, I get IO errors.

I opened it up and cleaned the head (which wasn't terribly dirty), but that didn't make any difference.

What else could've gone wrong with it? It's possible it got bumped around a little bit in the drawer but mostly it's just been sitting.

Offline
Last seen: 1 week 1 day ago
Joined: Jun 12 2022 - 23:35
Posts: 111
Was the drawer indoors or

Was the drawer indoors or outdoors?   If it was outdoors, thermal cycling can cause problems.  You can possibly get cracked solder joints or chips loose in their sockets.  If there was condensation there can be oxidation or rust on components.

Electrolytic or tantalum capacitors can age as well.  Sometimes you can tell if there is a problem by testing the power supply rail.  A bad capacitor can cause a lot of current draw and the voltage to sag.

It could also be a mechanical problem, for example, lubrication of the stepper motor or rails may be required.  Also the drive belt may be loose or worn and need replacement or tightening.

 

 

 

Offline
Last seen: 1 month 3 weeks ago
Joined: Apr 23 2022 - 18:41
Posts: 103
There are 4 logic chips of

There are 4 logic chips of the analog board. That’s the board you see when you remove the case. They’re all socketed so very easily replaced.  One controls the read cycle one controls the write cycle. Etc.  I forget which is which but I’ve had the write cycle one fail in me where the drive stopped formatting disks. One of the 4 ICs is labeled 74LS125. Notorious for blowing. If the ribbon cable is accidnently put on the controller card a row off it will blow causing the drive to just spin.  I’ve had several of these blow on me due to my poor eyesight installing the cable.  Cleaning the head was a good start. Did you clean the rails the head rides on as well?  Make sure the head is moving freely on the rails. Sitting for long periods of time they can stick on the rails preventing  the head from moving properly.  I’m far from an expert on these drives but I’ve had pretty good success in repairing several drives with issues like yours.  The logic chips I mentioned are all readily available from distributors such as Jameco and fairly inexpensive . I would start with the LS125 as I mentioned. A drive just spinning endlessly is one of its symptoms.  Also check the cable for continuity and signs of visible damage. I’ve had cables that looked fine but told me every disk was write protected. Cable was bad.  Those are items I would personally check first based on my personal experience with these drives and what commonly goes wrong with them. Granted it could be something deeper but I’d start there. 

CVT
CVT's picture
Offline
Last seen: 19 hours 9 min ago
Joined: Aug 9 2022 - 00:48
Posts: 1168
My Disk ][ has to be at least

My Disk ][ has to be at least this far from my Sony Trinitron in order to work. If I move it any closer it will not boot and I also get I/O errors if I try to read from it. I am not saying this is what's wrong with yours, I'm just putting it out there as a possibility, since I had the same situation where it was working perfectly before (without that TV of course), it just sat in a drawer and then it was broken. 

 

MacFly's picture
Offline
Last seen: 4 hours 43 min ago
Joined: Nov 7 2019 - 13:49
Posts: 484
Before swapping components or

Before swapping components or heating up your soldering iron: did you check the drive's speed? There is a trimmer on the motor controller board and a 50/60 Hz strobe disk on the bottom of the drive, which works fine with any incadescent light source (anything that slightly flickers with the frequency of your mains power). It's a pretty simple test/calibration step. It's described in many forum posts.

That would be the first thing I check, since it's the least invasive.

Offline
Last seen: 5 hours 47 min ago
Joined: Jun 18 2010 - 13:54
Posts: 795
 CVT wrote:My Disk ][ has to

 

CVT wrote:

My Disk ][ has to be at least this far from my Sony Trinitron in order to work.

You should try adding some shielding to the monitor case. Ideally, some aluminum foil along the right side of the monitor connected to ground. If you're willing to remove the case, you could do this on he inside.

CVT
CVT's picture
Offline
Last seen: 19 hours 9 min ago
Joined: Aug 9 2022 - 00:48
Posts: 1168
That would definitely help. I

That would definitely help. I also have aluminum tape for chimneys, which would be even better. Monitors are shielded like crazy, but TVs like this one have absolutely no shielding inside - just a plastic cover and that's it.

Offline
Last seen: 2 years 2 months ago
Joined: Sep 23 2022 - 21:30
Posts: 3
Thanks for all the ideas and

Thanks for all the ideas and suggestions!

I think it turned out to be an issue with the drive speed. I did the incandescent light bulb thing and it was pretty noticeably off. Once I got that adjusted and did a little more cleaning inside, it gradually started to work.

At first it showed a lot of errors when I tried verifying disks with Copy II+, but as I continued to exercise the drive they reduced in frequency and went away. Maybe the sled was kind of stuck and needed to be loosened up? Anyway, it now seems to be working fine.

Offline
Last seen: 1 day 5 min ago
Joined: Dec 19 2008 - 21:01
Posts: 415
Those rainbow cables are

Those rainbow cables are completely unsheilded, which was a big problem like this early on.

They replaced them with the thick sheilded grey cables to fix this.

 

Offline
Last seen: 1 year 10 months ago
Joined: May 27 2009 - 01:37
Posts: 1002
Be sure and reseat all the

Be sure and reseat all the cables. Clean them with Deoxit or similar. Just to be thorough.

Offline
Last seen: 1 month 3 weeks ago
Joined: Jul 5 2018 - 09:44
Posts: 2587
One thing that deteriorates

One thing that deteriorates on these drives over time is the belt.  It's some kind of rubber/fiber composite and it will dry rot or something over the years and harden or even fall apart.

 

I think there may be replacements for these, but not sure where to get them.

 

 

Offline
Last seen: 12 hours 40 min ago
Joined: Jun 6 2020 - 10:50
Posts: 451
Console5 sells drive belts.

Console5 sells drive belts. They specifically list the Apple Shugart drive belts. But don't list the Alps ones. At least not as Apple. They do sell Alps belts for the Commodore 1541.

 

 

Which having looked at both an Apple Alps and a 1541 Alps chassis, I see no reason they aren't the same belt. I've never had a reason to try them on an Apple Alps. But would have no reservations trying them if I needed one. 

Offline
Last seen: 1 month 3 weeks ago
Joined: Jul 5 2018 - 09:44
Posts: 2587
nick3092 wrote:Console5 sells
nick3092 wrote:

Console5 sells drive belts. They specifically list the Apple Shugart drive belts. But don't list the Alps ones. At least not as Apple. They do sell Alps belts for the Commodore 1541.

 

 

Which having looked at both an Apple Alps and a 1541 Alps chassis, I see no reason they aren't the same belt. I've never had a reason to try them on an Apple Alps. But would have no

 

Thanks for the info!  That's good to document out there!

 

Offline
Last seen: 3 days 6 hours ago
Joined: Apr 26 2016 - 08:36
Posts: 739
nick3092 wrote:Console5 sells
nick3092 wrote:

Console5 sells drive belts. They specifically list the Apple Shugart drive belts. But don't list the Alps ones. At least not as Apple. They do sell Alps belts for the Commodore 1541.

Which having looked at both an Apple Alps and a 1541 Alps chassis, I see no reason they aren't the same belt. I've never had a reason to try them on an Apple Alps. But would have no reservations trying them if I needed one. 

 

I am 99.9% certain that the belt that fits on the 1541 drive will also work on the Apple II Alps based mechanism.  Mind you, there were two flavours - the metal case Disk II Alps and the Aple 5.25"" Alps.  I believe that the belts are interchangable between them but I will have to verify.

 

 

Offline
Last seen: 1 month 3 weeks ago
Joined: Jul 5 2018 - 09:44
Posts: 2587
I'm thinking I should order a

I'm thinking I should order a few spares for both Shugart and Alps just to be on the safe side in case these become unavailable....

 

 

 

 

Log in or register to post comments