Custom Enclosure - Floppy Emu

198 posts / 0 new
Last post
PTB
Offline
Last seen: 9 hours 33 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
I contacted Steve as I had

I contacted Steve as I had some other questions for him and I asked him about this while I was at it.

 

The following is what he mentioned regarding the noise when his supplied OLED display is swapped out for the larger one in the kit.

 

From my experience the audio speaker in the IIgs is sensitive to RF and similar interference. For example I can hear a slight background noise when the Floppy Emu is accessing the SD card. The jumbo OLED probably requires more current or causes larger voltage swings on the power supply lines, which somehow get coupled to the speaker inputs and create noise. Part of this is probably a design weakness of the IIgs speaker, if its audio amplifier power and signal inputs aren’t well isolated and filtered. You might see some improvement by using the the shortest practical disk cable, locating the Floppy Emu further away from the IIgs (which I know contradicts the short cable), or looping the disk cable several times through a ferrite ring magnet. It might also help to add an extra large-value capacitor between +5V and GND or +3.3V and GND on the Emu end of the cable, the Emu board, or the jumbo OLED PCB. It will probably need some experimentation. I’ll ask some people from my amateur radio club if they have any other suggestions, since this is a common sort of problem for radios too.

 

Might be worth trying the ferrite ring idea in the first instance. When I found the old apple ii it had a cable like that with it.

 

 

Its something to try anyway.

 

He was also fine with me posting the pixelshift firmware update here in the forum thread, so I will dig that out and post in this thread as well.

 

Cheers

Dave

Offline
Last seen: 7 months 1 week ago
Joined: Jan 1 2021 - 09:56
Posts: 26
How did you do it? Did you

[[removed -- question was already answered]]

Offline
Last seen: 4 months 2 weeks ago
Joined: Apr 24 2022 - 00:15
Posts: 5
Thanks for the detailed reply

Thanks for the detailed reply Dave.  The ferrite ring idea is definitely one to try.I am also going to disconnect the internal speaker and test external speakers on the GS to see if the noise follows to the external speakers.

 

-- Bruce

 

Offline
Last seen: 4 months 2 weeks ago
Joined: Apr 24 2022 - 00:15
Posts: 5
The noise follows to the

The noise follows to the external speakers as well on the GS.

-- Bruce

 
bruce1000 wrote:

Thanks for the detailed reply Dave.  The ferrite ring idea is definitely one to try.I am also going to disconnect the internal speaker and test external speakers on the GS to see if the noise follows to the external speakers.

 

-- Bruce

 

 

PTB
Offline
Last seen: 9 hours 33 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
Just a quick heads up....

Just a quick heads up....

 

Head on over to Big Mess O Wires for an awesome firmware update for the floppy emu.

https://www.bigmessowires.com/2022/11/22/floppy-emu-new-smartport-ui-and-settings-menu/

 

Steve has done an awesome update that has lots of UI improvements and is looking after all us Jumbo display folks with selectable display types as well.

This takes care of the 2 pixel shift evident on the larger displays. In the past he had made a special firmware to fix it, but now it is rolled into the same firmware.

Sensational !!!

 

Dave

PTB
Offline
Last seen: 9 hours 33 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
Also.... has anyone with the

Also.... has anyone with the sound issue on the iiGS and the large display tried a ferrite ring or two yet?

Did it have any effect?

Offline
Last seen: 2 weeks 1 day ago
Joined: Aug 12 2022 - 14:40
Posts: 30
the new firmware is

the new firmware is absolutely stunning! Steve did a great job.  

clockchip's picture
Offline
Last seen: 1 week 17 hours ago
Joined: May 23 2018 - 16:33
Posts: 26
ferrite ring

i tried, but it had no effect on the sound issue.

jwg1962's picture
Offline
Last seen: 18 hours 28 min ago
Joined: Jan 29 2012 - 07:17
Posts: 363
Hi Dave, Is there a trick to

Hi Dave, 

Is there a trick to getting the new 2.4" display to work? i.e. Brightness etc.  Mine doesn't seem to turn on.  I put the old display back on the header and it worked, the new stays dark.   I ordered another one off Amazon to try. It will be here Saturday.  Everything else works perfectly and was very easy to solder.   

 

I thought I was very careful installing it and soldering the header on it.  Is there an easy way to test it outside of the unit? 

Thanks,

Jay 

 

PTB
Offline
Last seen: 9 hours 33 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
Hi Jay,Can't say I've had

Hi Jay,

Can't say I've had that problem. Off the top of my head here are some things to try.

 

1. Is the cable reversed. plugged in 180 degrees around wrong way?

2. Are you able to check the 7 wire harness with a multimeter. Does each strand have continuity?

3. Do you have an arduino? I Can point you to or send you an arduino sketch to check it.

 

I'll have a bit more of a think as to what else can be tried.

 

If it still fails PM me and we can try get it sorted.

 

Cheers

Dave

jwg1962's picture
Offline
Last seen: 18 hours 28 min ago
Joined: Jan 29 2012 - 07:17
Posts: 363
PTB wrote:Hi Jay,Can't say I
PTB wrote:

Hi Jay,

Can't say I've had that problem. Off the top of my head here are some things to try.

 

1. Is the cable reversed. plugged in 180 degrees around wrong way?

2. Are you able to check the 7 wire harness with a multimeter. Does each strand have continuity?

3. Do you have an arduino? I Can point you to or send you an arduino sketch to check it.

&nb

 

Nope the plug is good  gnd->gnd  etc 

 

I put the old screen on the 7 pin harness and it worked so I am assuming it has continuity. 

 

I do have an arduino.  -- several different models. 

 

 

Thanks,

Jay 

 

Offline
Last seen: 1 week 5 days ago
Joined: Jun 25 2020 - 17:00
Posts: 219
Emu update 221128A

After using the emu hack setup long enough to confirm I could select and load disk images and booth them using the Apple Disk ][ controller. I set it aside.

 

After seeing the new emu firmware update excitement, I decided to download and install it.  But during the installation procedure I noticed the Select button was sticking when pushed.  As a result I cannot reliably navigate through the emu menus.  

Upon investigating the pb sticking problem I found that the bottom push buttons center pretty well in their panel holes but the top ones are slightly off, the Select pb being the worst since it scrapes against the hole in the 10'oclock position.  All pb's are perfectly flat against the circuit board, no tilting at all.  I haven't seen anyone else mention this so it must be unique to me.

 

I did state in an earlier post that I thought the hole tolerances in general were way to tight.  If I slightly loosen the 4-40 nuts (or whatever they are) holding the switch pcb, the Select button works better but still rubs.  When these nuts are snug, the rubbing gets worse.

 

Had the push button pcb board mounting holes been slight oversized, allowing the pcb to be adjusted for optimal location of the push button caps in their holes this could have been easily resolved.

 

 

 

 

I am using the green display and after the latest firmware update I see vertical lines on the first two rows of text, shown here. And I should mention that I switched to using the Apple I/O Controller (aka 5.25" Disk Controller) just druing this firmware change.  Haven't figured out how to navigate the menus to allow me to designate one disk image for Drive 1 and another for Drive 2.  That's the whole reason I changed to the newer controller.

 

 

 

 

Any suggestions?

 

Thanks

 

 

Offline
Last seen: 1 week 5 days ago
Joined: Jun 25 2020 - 17:00
Posts: 219
Problem resolved

I dismounted the PB pcb and used a rat-tail file to auger the 4 holes a bit larger (barely perceptable).  Then I measured the I.D.'s of the pcb's mounting holes...they were all .105", so I used a .106" drill and augered out the pcb mounting holes by .001".  Remounted everything and now all is well, no sticking buttons.

 

I found the Emu manual and set the display type to 2.4" and the Disk mode to 5.25" Dual Disk and all is well!

 

I love the emu...but the CFFA is so much easier to use, but I will be using both, together.

clockchip's picture
Offline
Last seen: 1 week 17 hours ago
Joined: May 23 2018 - 16:33
Posts: 26
IIgs noise

Hello,

today I installed a floppy controller from my other Apple II into the IIgs and connected the floppy emu.

Unfortunately, I still have these noise problems. As mentioned above a ferrite core on the floppy cable didn't help either. Due to this interference, it is unfortunately impossible to use the modded floppy emu for a longer period of time without going crazy. 

It would be great if someone had an idea of how to solve this problem on the IIgs. 

regards clockchip

 

PTB
Offline
Last seen: 9 hours 33 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
@clockchip and

@clockchip and @bruce1000

Still trying to think of what can be done with the IIGS noise.

I did find similar problems in a thread over at Vintage Computer Federation forums. Not sure what rules are for posting links to other forums.

But googling IIGS noise will bring it up in the first couple of search results. In there is talk about ROM03 being better for noise than Rom01.

I know nothing about the IIGS so I'm not sure what that means. Not solving it but helpful background info.

 

@Lasermaster

Yeah I did go pretty tight on the clearances with the buttons. I wanted to not be able to see a gap between button and panel. I had assembled and disassembled several times while making it and once a rubbing squeak had developped on one of the buttons. For me taking it apart and putting it back together did the trick but I agree with what you are saying. Another 0.1mm of clearance may not of been a bad idea. Mine is currently working fine with no rubbing or sticking without modding, but your solution is a good one if anyone else gets the same issue.

 

 

Edit - I just saw you got the menu stuff sorted, but I already typed it out and will leave it for anyone else. I really need to read things better :)

As far as getting the display to fix the 2mm pixel shift just need to do the following.

Hit select immediately after startup to get settings menu.

Go down to 4th option "Display Type"

Select Jumbo 2.4"(SSD1309)

 

To get dual disk mode its a similar deal

Hit select immediately after startup to get settings menu.

Go down to 2nd option "Disk Emulation Mode"

Select Apple II Dual 5.25

Restart computer

 

@JWG1962

An extra thing to check....I was wondering if you can get a photo of the back of the display, particularly R3 R4 and R5.

Those resistors are for configuring between I2c and SPI. Maybe it came from factory incorrectly configured.

 

I think this is incredibly unlikely and that the display is actually faulty and we can sort that out, but would be good to check. Have PM'd you as well.

 

Cheers

Dave

 

 

 

 

Offline
Last seen: 1 week 5 days ago
Joined: Jun 25 2020 - 17:00
Posts: 219
@LasermasterYeah I did go

@Lasermaster

Yeah I did go pretty tight on the clearances with the buttons. I wanted to not be able to see a gap between button and panel. I had assembled and disassembled several times while making it and once a rubbing squeak had developped on one of the buttons. For me taking it apart and putting it back together did the trick but I agree with what you are saying. Another 0.1mm of clearance may not of been a bad idea. Mine is currently working fine with no rubbing or sticking without modding, but your solution is a good one if anyone else gets the same issue.

 

I'm sure your push button panel hole sizes could stay as they are if you just enlarged the push button pcb mounting hole diameters by .10mm, maybe a bit less but enough to shift the pcb aroung a bit and get all four buttons to be centered on their holes during tightening of the nuts on the pcb standoffs. 

 

 

jwg1962's picture
Offline
Last seen: 18 hours 28 min ago
Joined: Jan 29 2012 - 07:17
Posts: 363
@JWG1962An extra thing to

@JWG1962

An extra thing to check....I was wondering if you can get a photo of the back of the display, particularly R3 R4 and R5.

Those resistors are for configuring between I2c and SPI. Maybe it came from factory incorrectly configured.

 

 

Hi Dave, 

 

Here is the pic of the back.  Note there is a dimple in the plastic on the ribbon cable, but I looked under a microscope and it is superfical.   I just put that in there taking it back out of the device. 

 

It looks right.   i.e.  Only R4 is installed for SPI. 

 

Thanks,

Jay 

 

Offline
Last seen: 4 months 2 weeks ago
Joined: Apr 24 2022 - 00:15
Posts: 5
Thank you Dave.  I was toying

Thank you Dave.  I was toying with the idea of purchasing a different larger oled, to see if that makes a difference, but I don't think that it will, especially if it uses the same chipset

I read about the Rom03's having much better sound protection circuitry than the Rom0's and Rom01's.  The problem for me is that I am using this with a Stealth IIGS, so I need to the keyboard connector to be able to connect the IIe keyboard to the IIGS motherboard.

For now, I just use the standard floppy emu without the Disk II enclosure / larger screen, due to the noise.

Really looking forward to find a way to fix this noise too.

Thanks!

-- Bruce

 

 

 
PTB wrote:

@clockchip and @bruce1000

Still trying to think of what can be done with the IIGS noise.

I did find similar problems in a thread over at Vintage Computer Federation forums. Not sure what rules are for posting links to other forums.

But googling IIGS noise will bring it up in the first couple of search results. In there is talk about ROM03 being better for noise than Rom01.

 

Offline
Last seen: 11 months 2 days ago
Joined: Dec 10 2022 - 04:53
Posts: 4
Stickers? What stickers?

Stickers? What stickers?

https://www.etsy.com/uk/listing/925798264/apple-logo-sticker-apple-logo-stickers?ref=sim_items_grid_ad-3&plkey=ee7135ce23db794184cb5c3b98a9a8ecaadd7682%3A925798264

Just sayin'

(5 minutes later... There's dozens of them! Curses on these intertubes!)

jwg1962's picture
Offline
Last seen: 18 hours 28 min ago
Joined: Jan 29 2012 - 07:17
Posts: 363
 I have a whacky suggestion

 

I have a whacky suggestion to attemp to isolate the "noise" source.   Has anyone created a small "Faraday Cage" out of tin foil and placed it over the disk II enclosure to see if that is the source or the ribbon cable is where the leak is coming from.    If it is the Disk II case,  you may be able to line it with laminated tin foil to block the RF.   Like I said, pretty whacky.  :-) LOL! 

 

Online
Last seen: 22 min 16 sec ago
Joined: Jun 6 2020 - 10:50
Posts: 408
Might be related, might not

Might be related, might not be. When I had my Phasor clone in my ROM3, it picked up all kinds of noise from a stock floppy emu. Any time there was drive access, I could hear some noise in the speakers hooked up to the phasor. It may just be the IIgs bus picks up noise easily. Granted nothing from the IIgs speaker that I noticed. Just the Phasor card picked up the access noise. Can't say I've noticed the same with the Phasor in my IIe now. 

jwg1962's picture
Offline
Last seen: 18 hours 28 min ago
Joined: Jan 29 2012 - 07:17
Posts: 363
On Vacation now - Finally got the Floppy EMU Case assembled!!

Thanks Dave  -  This Kit is freakin' awesome.   I finally got it assembled.  The only issue I had was the bad display.  The ones from Amazon worked perfectly.  I posted a picture on them.  The only MOD I did was replaced the RED and GREEN LEDs with Blue and Gold ones.  I work at the University of Pittsburgh in the IT department and Blue and Gold are the school colors.  They are high intensity LEDs that one could most likely see from orbit, but I am not messing with them any more.   Everything works as advertised.    Thanks to Retro Bill for printing the 3D parts. 

 

I love it and will be hauling it to KansasFest this year.   Thanks again.  

 

Well,  I guess you can;t see the blue and gold in the picture, so you will just have to take my word for it.  Ha Ha :-)  

 

Thanks,

Jay 

macnoyd's picture
Offline
Last seen: 2 days 8 hours ago
Joined: Oct 15 2012 - 08:59
Posts: 836
Looks awesome!

Looks awesome!  I need to assemble mine soon.  I'll be using a modified Disk 2 faceplate but the results will look much the same.

Nice work.

PTB
Offline
Last seen: 9 hours 33 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
Thats brilliant Jay. Glad you

Thats brilliant Jay. Glad you like it and it all came together in the end with a new display. :)

Blue leds against black background always looks good. Be very cool to see it make an outing at Kansasfest too.

Which reminds me, I need to keep looking at what went on there this year.

Thanks for the kind words on the kit.

 

Cheers

Dave

jwg1962's picture
Offline
Last seen: 18 hours 28 min ago
Joined: Jan 29 2012 - 07:17
Posts: 363
Thank you
Oooh! I forgot I bought the clear MacEffects top for the DIsk II. I am going to put that one on this and see how it looks. Jay
Offline
Last seen: 2 weeks 1 day ago
Joined: Aug 12 2022 - 14:40
Posts: 30
Disk Knocker

Is anyone using a Disk Knocker with their setup? in order to make the drive seem more authentic? 

 

PTB
Offline
Last seen: 9 hours 33 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
Hi Microbmen....Not Yet....
Hi Microbmen....Not Yet.... But I have plans. :)

 

If only I had some free time to go with those plans ;)

Cheers

Dave

Offline
Last seen: 2 weeks 1 day ago
Joined: Aug 12 2022 - 14:40
Posts: 30
 PTB wrote:Hi Microbmen...
 
PTB wrote:

Hi Microbmen....Not Yet.... But I have plans. :) 

Let me know your findings,  Once I added the Noisy Disk Knocker my FEMU goes into a reboot loop.  I tried it on another iie and it works fine.  Seems that the 2.4" display + the Noisy Disk results in too much power draw for some PSUs. It could also be controller related, I havent tested that yet.  If I pull out the 2.4" display and put back the 1.3" display it works fine. 

 

 

 

 

 

 

 

Offline
Last seen: 2 weeks 1 day ago
Joined: Aug 12 2022 - 14:40
Posts: 30
Did someone say what does it

Did someone say what does it look like in a clear case?  I added a blue led from a tee off the power line. 

PTB
Offline
Last seen: 9 hours 33 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
That looks pretty wild. :)

That looks pretty wild. :)

Offline
Last seen: 3 weeks 6 days ago
Joined: Mar 23 2022 - 19:42
Posts: 8
Finally had time to build mine out.

Okay I finally had time to build this out and get it working.

 

Two questions:

 

1 - Remind me why the LED holes are OVERSIZED, creating the need for a 3d printed rear bezel just to plug the gap so the ncluded LED bezel will fit?

Was there a resaon we didn't just make the LED hole the size of the included bezel?

 

2- Did all the kits sell out or are there any more available? How about parts like the button board?

-neal

PTB
Offline
Last seen: 9 hours 33 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
Hi nglayton, Sorry for

Hi nglayton,

 

Sorry for delayed response. I've been away and was out of contact.

 

1. I thought I had posted this but, going back through everything i realised I hadn't. Basically it was an early error on my part that I decided to keep as i thought it had some spinoff benefits.  I got approached sometime ago to do an article about how the project was developed. In the end that never happened as far as I know, but there is a paragraph in there that explains what happened with those bezels. I'll post what I wrote here in this thread shortly.

 

2. They are pretty much answered for now. I have 3 or 4 people I need to touch base with to see if they are still possibly interested. They were in first and I wish to give them final say. I have three left and one slightly dodgy one I was going to discount a bit as it has a blemish in the printing from all my experimentation on it with the logo woes. I tried a lot of things on that panel. I thought I had sanded it sufficiently for the reprint process. I hadnt. It still looks pretty good head on, cant really see it without searching for it, but on the right angle... I can see the old areas I had been testing on. This may or may not become available pending current queries. Images of it below.

 

I have no spare parts, like the pcb or the OLEDS, I just got enough to do the kits. I do have some of the other things though, but postage for the odd bits would be uneconomical.

That being said though, I still intend to release all the files once the last one I have outlaid for is sold. I don't intend to do another run.

 

Cheers

Dave

 

 

Offline
Last seen: 3 weeks 6 days ago
Joined: Mar 23 2022 - 19:42
Posts: 8
No worries

Don't worry about the delayed response.  PM sent

jwg1962's picture
Offline
Last seen: 18 hours 28 min ago
Joined: Jan 29 2012 - 07:17
Posts: 363
I showed mine off at

I showed mine off at KansasFest and it was a hit!!!!

 

Offline
Last seen: 3 hours 2 min ago
Joined: Nov 29 2020 - 19:48
Posts: 127
I finally finished the first of 2 builds!

I finally finished the first of 2 Disk ][ FEMU hacks. Here is a picture and a couple of notes

1) The Next button tended to stick due to mechanical binding. The second one I am assembling has a similar problem with the Previous button.  Still a very minor thing. Not the same buttons as someone else reported.  The tolerance is close so minor angles in soldering the switches might be the source of the problem. I ended up taking it all apart and used a round file on the hole with the sticky button, but was not really satisfied with the direction it was going.  I accidentally left off the spacer by the sticky button during a test fit and it all worked!  So, I screwed the board down with the nut on the post as a backer to avoid too much board flex and no spacer between the faceplate and board.  No more sticking! That gives it just enough slop to unstick itself.  I added a  little fingernail polish to hold the nut in place and called it good.  Still a very minor thing.

2) The headers and header pins on the extention cables are a little sloppy causing the panel to dim sometimes. So, I tacked most connections with hot glue for stability. No problems now.

3) I had a Noisy Disk noise maker for track to track movement.  When I installed it, my unit it would reset just like an earlier post described.  I agree probably not enough power for the Noisy Disk and larger display from a Disk ][ controller.

4) I added a 3d printed colored logo label from Ebay to the front. 

 

Now Javier's 3.5 case is tempting...

 

 

 

magnusfalkirk's picture
Online
Last seen: 8 min 33 sec ago
Joined: Feb 18 2007 - 11:46
Posts: 325
Thank you again

Rich thank you again for putting my FloppyEMU in the case. It looks great. Finally got things straightened up in my computer room so I can plug the FEMU into the ROM 03 GS and be off to the races!

PTB
Offline
Last seen: 9 hours 33 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
Very Cool Jay :) You are now

Very Cool Jay :) You are now the head of marketing ;) Thanks !!!

 

8bitheaven.

 

1)Good solution. Mine too was sticking at one point and unscrewing it and redoing it seemed to fix it. I think it all comes down to luck. I definately had the tolerance too fine when I sized those holes.

2)I'll keep an eye out for that. Again... good solution.

3)Bummer. I bought a noisy disk to put in mine and I havent had time to yet. I hope it works but from what you are saying it sounds like it wont for me.

4)Its a bit larger than original, but man that pops. Looks great. I spent a fair bit of time originally trying to replicate the raised logo in the panel, but ended up going flat.

 

 

Magnusfalkirk

I hope it works. I dont have a GS but I'm hearing the kit has noise issues on GS. Fingers crossed it doesnt in your case.

 

Cheers

 

Dave 

PTB
Offline
Last seen: 9 hours 33 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
Further up I mentioned an

Further up I mentioned an article I was asked to write about the hack.  I wrote it for Call Apple. Bill Martens kindly sent me a copy of the final article which appeared in Volume 32 Number 2. So if you want to see it in that form plus other better articles, thats where to go.

 

He was also cool with me to repost the particular article here. Here it is in its original form. I'm not really a literary guy, so it may be a bit rough ;) 

 

The article explains the background to creating it and may answer some questions that have been asked as to why some things ended up the way they are.

 

 

https://www.applefritter.com/files/2023/08/07/Case%20Hack%20for%20BMOW%20Floppy%20Emu%20-%20Floppy%20Emu%202.pdf

 

Cheers

 

Dave

 

 

magnusfalkirk's picture
Online
Last seen: 8 min 33 sec ago
Joined: Feb 18 2007 - 11:46
Posts: 325
Really good article

Dave, I clicked the link and read through your article describing how you came up with the case hack for the FloppyEMU. Great article and of course a great hack!

Offline
Last seen: 2 months 2 weeks ago
Joined: Oct 2 2018 - 13:54
Posts: 4
Does this mean there might be

Does this mean there might be one still for sale? If so I would like to purchase it!

Offline
Last seen: 2 months 4 days ago
Joined: Aug 24 2023 - 01:59
Posts: 5
From what I understand from

From what I understand from Dave, all his kits are gone. He plans to release the files once he cleans them up a bit but it may take a couple of months... I asked him about this about 2-3 weeks ago.

PTB
Offline
Last seen: 9 hours 33 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
Thanks HeyMerlin. Spot on. Hi

Thanks HeyMerlin. Spot on.

 

Hi dragos,

 

Yes unfortunately they are all now gone. I will be posting the files and info for people to run with.

Most likely under a creative commons Attribution-Sharealike licence.

 

I really need to get onto this and tidy them up. My intent is to post them here at applefritter.

Will also post links for the switches and stuff, though most parts can be gotten from anywhere.

 

And thankyou everyone who bought one.

 

Cheers

Dave 

Offline
Last seen: 2 months 4 days ago
Joined: Aug 24 2023 - 01:59
Posts: 5
Releasing of files

Hey Dave,

 

Just thinking out loud here (well as loud as my keyboard clacks away)...

 

Have you considered releasing the files on GitHub? This way multiple people could contribute changes or alterations or alternate versions and have it all in one location.

Of course, since I'm new to AppleFritter, this may also be an ideal location for them.

 

It would be nice if there was a way of getting your version and some of the alterations all in one place so a person could look them over and decide which way to go.

 

 

Offline
Last seen: 6 months 1 week ago
Joined: Jan 17 2020 - 04:02
Posts: 9
Another happy user

Hi,

 

I finally got  some time to put together Dave's kit and Bill's 3D printed parts. Before starting I was very nervous about the soldering on to the SMD resistors and LEDs but that turned out to be really quite simple! The issue for me was the very tight spacing around the navigation buttons and actually screwing the various bits together. Got there in the end and it looks simply stunning! So thanks Dave for the countless hours you must have spent on refining this idea into a very professional product and thanks Bill for helping those without a 3D printer and providing very sturdy parts!

 

Dave

 

 

 

PTB
Offline
Last seen: 9 hours 33 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
Thanks dhoggan :)Heymerlin, I

Thanks dhoggan :)Heymerlin, I'm not really a github guy. Yet anyway. Who knows what the future holds.I reckon eventually it would disappear into the github soup and be hard to find.

I also like how Tom has gone all out on this website including the 100 year plan. This joint is a onestop shop for great info, so I'm pretty keen on just parking it here. :)Cheers

 

Dave

Offline
Last seen: 2 months 2 weeks ago
Joined: Oct 2 2018 - 13:54
Posts: 4
files

Any idea when you might release the files? would love to make a few of these for our retro club!!

 

Thanks!!

PTB
Offline
Last seen: 9 hours 33 min ago
Joined: Aug 14 2020 - 07:01
Posts: 111
Hi dragos, They have been

Hi dragos,

 

They have been posted in a new thread. 

 

https://www.applefritter.com/content/custom-enclosure-floppy-emu-source-files

 

 

I should have posted a link here as well ;)

 

Cheers

 

Dave

 

Pages

Log in or register to post comments