Apple II

New to my Apple iie, stumped on ADTpro

Submitted by Dan in Vermont on April 4, 2021 - 9:17pm

Hello.

 

I've been working on my Apple iie, and I'm stuck on the transferring a disk part of ADTpro. I get the ADTpro PORSOS and serial transfer, it's all good there. I'm getting the Host Timeout error when I try to hit enter at the file name prompt to show the list of disks in my directory on the windows laptop.  

Forums: 
Apple II

2e motherboard with 1 Ohm over the 12V

Submitted by Lowlander on April 4, 2021 - 10:06am

Hi hi

 

Was testing a 2e yesterday. It booted but after a few seconds went down with the psu making worrying noises.

At first thought it was the PSU, so switched a working one on it, but only made same noises.

Then measured the V's of that one and compared them to the first one and all looks good.

So the 2e board itself...

Measured resistance over the power lines; - V's are good. +5 was just some 10 Ohm, but went high when i unplugged keyboard. Seems to be the light in there that makes the resistance low, bc it seems to be a an actual tiny lightbulb.

Forums: 
Apple II

Apple IIe: switch floppies without restarting computer

Submitted by coolk on April 4, 2021 - 3:04am

Is it possible to stop currently loaded program and start a new one by switching out the floppy at runtime?

I'm using emu to load a tun of .dsk image files on an se card. When I select an image, nothing happens. But if I switch off in that state and switch on again then the program loads. However if I "eject" that image, select a different one and hit empty apple+ctl+reset then I just see apple][ logo and nothing happens.

So my question is, is it possible to load a new program/game without switching the computer off and on?

btw, I'm new to vintage apple computer world.

Forums: 
Apple II

Testing Disk II without the computer

Submitted by Stargeezer on April 3, 2021 - 5:35pm

Has anyone ever tested a Disk II drive without the controller or computer?

I want to see if there are any electro-mechanical reasons the drive isn't spinning on machine powerup.  This is also to help diagnose slot, vs card vs drive problem.

Forums: 
Apple II

Apple IIc monitor European vs USA

Submitted by Tomex on April 2, 2021 - 3:51pm

Hello,

I am looking for a green monochrome monitor for my Apple IIc. While searching I asked myself  a question:

since the IIc's composite output is PAL or NTSC depending on region, is there a similar difference in monitor?

 

In other words, would the US monitor work with European IIc (or vice-versa)?

 

I may lack a deeper understanding of PAL vs NTSC, which I understand define color coding, so I thought about asking smarter people.

 

Forums: 
Apple II

Fingerprint board for Apple IIc

Submitted by MajorMar on April 2, 2021 - 2:25pm

I recently picked up this Apple IIc and discovered it had a fingerprint board inside which is tapping directly into the CPU.

Forums: 
Apple II

Apple II+ Mystery Card

Submitted by Paul19804 on April 1, 2021 - 9:03am

Recently acquired a 48K Apple II+ (tagged 8047) with genuine Apple dual-disk controller and an Apple II floppy drive.  It's cleaner than my Apple II (tagged 7847) that I've had since its birth.

It came with an card that appears to be a single drive controller, but testing reveals it doesn't.  The previous owner was vague about the card's function.  Behind the glare, next to the ribbon connector, it is imprinted "Symtec 82"

Interesting side note:  It will fit in the Apple II+ slot, but will NOT fit in the Apple II slot; it's just a bit too long.  

Forums: 
Apple II

Apple II+ PAL -> NTSC mod issues

Submitted by blindowl on March 31, 2021 - 5:26pm

Hi all, 

Since my Apple II+ is modded for the PAL region and I don't have a PAL encoder card, it can't display color. So I decided to restore it to NTSC, but the result is not so successful.

 

As you can see in the video, the display is far too bright and unstable, with visible vertical bars. It is mainly in text mode that the image flickers, in color mode it is slightly more stable (but still too bright with visible bars).

Forums: 
Apple II

GS/OS 6.0.1 Locks Up loading

Submitted by dougcpa on March 31, 2021 - 3:08pm

I have a ROM 01 GS. I did have an old 5MB SCSI drive on this computer, but that drive died. Instead of replacing with another SCSI drive I've removed the SCSI controller card and replaceed it with a ReactiveMicro compact flash/IDE card installed in slot 7. The only other expansion card in my GS is a 4MB RAM card in the auxiliary slot.

 

Forums: 
Apple II

Pages

Subscribe to Apple II